digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130118 c106 series silicon controlled rectifier available non-rohs (standard) or rohs compliant (add pbf suffix). available as ?hr? (high reliability) screened per mil-prf- 19500, jantx level. add ?hr? suffix to base part number. maximum ratings rating symbol value unit peak repetitive forward and reverse blocking voltage (1) (r gk = 1k ? , t j = -40 to +110c) c106q c106y c106f C106A c106b c106c c106d c106e c106m v rrm , v drm 15 30 50 100 200 300 400 500 600 volts forward current rms (all conduction angles) i t(rms) 4 amps average forward current (t a = 30c) i t(av) 2.55 amps peak non-repetitive surge current (1/2 cycle, 60hz, t j = -40 to +110c) i tsm 20 amps circuit fusing considerations (t = 8.3ms) i 2 t 1.65 a 2 s peak gate power p gm 0.5 watts average gate power p g(av) 0.1 watts forward peak gate current i gfm 0.2 amps peak reverse gate voltage v grm 6 volts operating junction temperature range t j -40 to +110 c storage temperature range t stg -40 to +150 c mounting torque (2) 6 in. lb. note 1: v drm and v rrm for all types can be applied on a continuous basis. ratings apply for zero or negative gate voltage; however, positive gate vol tage shall not be applied concurrent with negative potential on the anode. blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. note 2: torque rating applies with use of compression washer. mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. anode lead and heatsink contact pad are common. soldering temperature shall not exceed 200c. for optimum results, an activated flux is recomm ended. thermal characteristics characteristic symbol maximum unit thermal resistance, junction to case r ? jc 3 c/w thermal resistance, junction to ambient r ? ja 75 c/w electrical characteristics (t c = 25c) characteristic symbol min. typ. max. unit peak forward or reverse blocking current (v ak = rated v drm or v rrm , r gk = 1k ? ) t j = 25c t j = 110c i drm, i rrm - - - - 10 100 a forward ?on? voltage (i fm = 1a peak) v tm - - 2.2 volts gate trigger current (continuous dc) (v ak = 6vdc, r l = 100? ) (v ak = 6vdc, r l = 100? , t c = -40c) i gt - - 30 75 200 500 a gate trigger voltage (continuous dc) (v ak = 6vdc, r l = 100? ) (v ak = 6vdc, r l = 100? , t c = -40c) v gt 0.4 0.5 0.60 0.75 0.8 1.0 volts
digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 c106 series silicon controlled rectifier characteristic symbol min. typ. max. unit holding current (v d = 12vdc, r gk = 1k ? ) t j = 25c t j = -40c t j = 110c i h 0.3 0.4 0.14 - - - 3 6 2 ma forward voltage application rate (t j = 110c, r gk = 1000 ? , v d = rated v drm ) dv/dt - 8 - v/s turn-on time t gt - 1.2 - s turn-off time t q - 40 - s mechanical characteristics case to-126 marking body painted, alpha-numeric pin out see below to-126 inches millimeters min max min max a 0.425 0.435 10.80 11.050 b 0.295 0.305 7.490 7.750 c 0.095 0.105 2.410 2.670 d 0.020 0.026 0.510 0.660 f 0.115 0.125 2.920 3.180 g 0.091 0.097 2.310 2.460 h 0.050 0.095 1.270 2.410 j 0.015 0.025 0.380 0.640 k 0.595 0.655 15.110 16.640 m 3 typ 3 typ q 0.148 0.158 3.760 4.010 r 0.045 0.055 1.140 1.400 s 0.025 0.035 0.640 0.890 u 0.145 0.155 3.680 3.940 v 0.040 - 1.020 - fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130118
digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 c106 series silicon controlled rectifier fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130118
|
